Highest Milage on an S
Moderators: Gromit, Paul, slparry
-
winger
Hi,
Just left mine in for it's 132,000 mile service.
Had it since new, only orginal bit is the seat and the engine block.
But the dealer creashing it caused a lot of new bits to appear.
Four drive line failures (3 sets of splines on the input shaft) and a rear drive waht-its-name turning to cheese.
It did 1.5 days at Cadwell park in July in the fast group.
Adrian
Just left mine in for it's 132,000 mile service.
Had it since new, only orginal bit is the seat and the engine block.
But the dealer creashing it caused a lot of new bits to appear.
Four drive line failures (3 sets of splines on the input shaft) and a rear drive waht-its-name turning to cheese.
It did 1.5 days at Cadwell park in July in the fast group.
Adrian
winger wrote:Hiya Malc
Where the hell have you been!!! we have to put with Blackbirds on this site so i'm sure war and piece about you Blade won't go amiss.
Hi Chris,
Not much to report really. I pop in for a read from time to time but don't post as I generally don't have anything to contribute. The Blade has gone through one alterator and one reg/rec and that's it. Haven't needed to adjust the valves yet and it's on the original clutch. Typical boring Honda I suppose although it does have a few quirks. The fuelling is appalling at town speeds and it likes new steering bearings every 15K (the front wheel never leaves the floor).
115k and one gearbox, one clutch(at 55k) and one shaft, rebuilt rear bevel(90k)
The odd bit falls off every now and then
, but nothing too major.
Three sets of paralever bearings, but so easy to change. Right hand heated grip is still going strong with hardly any rubber left on it (been through about 5 left hand ones!!)
Used a variety off oils, currently using Chevron synthetic £10 for 4 litres from Costco. Has never been serviced by any one but me, since I bought it with 5k on the clock.
Wouldn't part with the old girl for the world
Lennie's intake, Bbpower chip, San Jose filter, Laser exhaust, k12 fuel reg.
The odd bit falls off every now and then
, but nothing too major.
Three sets of paralever bearings, but so easy to change. Right hand heated grip is still going strong with hardly any rubber left on it (been through about 5 left hand ones!!)
Used a variety off oils, currently using Chevron synthetic £10 for 4 litres from Costco. Has never been serviced by any one but me, since I bought it with 5k on the clock.
Wouldn't part with the old girl for the world
Lennie's intake, Bbpower chip, San Jose filter, Laser exhaust, k12 fuel reg.
adrianw wrote:Hi,
Just left mine in for it's 132,000 mile service.
Had it since new, only orginal bit is the seat and the engine block.
But the dealer creashing it caused a lot of new bits to appear.
Four drive line failures (3 sets of splines on the input shaft) and a rear drive waht-its-name turning to cheese.
It did 1.5 days at Cadwell park in July in the fast group.
Adrian
the seat on mine is shagged after 39k...
everything else seems ok apart from usual cosmetic issues with fork legs and engine paint.
soggy rear OE shock which I would replace if I could be bothered.
one input shaft and clutch and paralever bearings plus a couple of clutch output seals when under warranty - they botched the first repair.. oh and a popped fork seal.
I think UV has killed the seat which is split where it creases under my weight... as the bike lives outside year round - all the switchgear and black plastic has faded.
Aside from that starts on the button every time
2000 R1100S Sport
1980 Vespa P125X
1980 Vespa P125X
Just a shade under 84k on my '99 1100s.
Only let me down once at 47k with a blocked fuel filter. A dealer charged me £167 to 'diagnose' and fix the problem, and that was the last time the bike ever went near a dealer.
Do all my own servicing and use Texaco semi-synth oil from Morrisons at £13 for 5L with the bike never using any oil between changes, but it does get an easy life being used for commuting and doing mostly motorway miles.
Original clutch, gearbox and bevel box, replaced: 1 set paralever bearings, 1 front disc, rear shock, rear silencers and two sets of front disc wavey washers.
Overall I'm pretty satisfied with it.
Only let me down once at 47k with a blocked fuel filter. A dealer charged me £167 to 'diagnose' and fix the problem, and that was the last time the bike ever went near a dealer.
Do all my own servicing and use Texaco semi-synth oil from Morrisons at £13 for 5L with the bike never using any oil between changes, but it does get an easy life being used for commuting and doing mostly motorway miles.
Original clutch, gearbox and bevel box, replaced: 1 set paralever bearings, 1 front disc, rear shock, rear silencers and two sets of front disc wavey washers.
Overall I'm pretty satisfied with it.
Hi all,
thanks for all of you who voted and responded. this thread had over 700 hits since started. so far 40 people have voted...
i am sure we have more people to come...
keep voting.
thx Lars
PS: i will be riding in Wales this weekend. I will be staying near Brecon, but may ride up to North Wales on Saturday. anybody from the forum up for a meet / ride together?
thanks for all of you who voted and responded. this thread had over 700 hits since started. so far 40 people have voted...
i am sure we have more people to come...
keep voting.
thx Lars
PS: i will be riding in Wales this weekend. I will be staying near Brecon, but may ride up to North Wales on Saturday. anybody from the forum up for a meet / ride together?
Lars1974 wrote:Hi all,
thanks for all of you who voted and responded. this thread had over 700 hits since started. so far 40 people have voted...
i am sure we have more people to come...
keep voting.
thx Lars
PS: i will be riding in Wales this weekend. I will be staying near Brecon, but may ride up to North Wales on Saturday. anybody from the forum up for a meet / ride together?
You're a weekend out. I just did all of that this weekend. It was great.
Who is online
Users browsing this forum: No registered users and 255 guests